Radium Engineering Fuel Pump Hanger Without Pumps for GSS342 Nissan S14 S15 R33 R34 50-1200

LATE MODEL FUEL PUMP HANGER

This product is compatible with the following vehicles:

For Nissan S14 Silvia (All models/trims/RHD/LHD)
For Nissan S14 200SX (All models/trims/RHD/LHD)
For Nissan S14 240SX (All models/trims/RHD/LHD)
For Nissan S15 Silvia (All models/trims/RHD/LHD)
For Nissan S15 200SX (All models/trims/RHD/LHD)
For Nissan R33 Skyline (All models/trims/RHD/LHD)
For Nissan R34 Skyline (All models/trims/RHD/LHD)

OVERVIEW
The Radium Engineering fuel pump hanger replaces the entire factory assembly. It can be configured with 1 or 2 aftermarket fuel pumps to meet the fuel demands of various high performance engines. Fuel pump options include Walbro (Ti Automotive) or AEM.

The functionality of the factory Nissan level sender, low fuel switch, and fuel temperature (OBD-II only) are retained. Adapter fittings are provided that permit direct connections for all factory fuel line variations (quick connect and hose barb). No extra fuel plumbing is required. As shown below, the adapter fittings can be changed for -AN style hoses as well (sold separately).

The OEM system uses a venturi jet pump to transfer fuel from the passive side of the tank to the active (pump) side of the tank. When using aftermarket high-flow pumps this venturi jet pump creates a restriction in the fuel return, resulting in unwanted backpressure and unmanageable fuel pressure. Radium Engineering has redesigned the siphon system to completely eliminate this restriction but still effectively scavenge fuel the same as factory.

NOTES:
1. Depending on fuel pressure, the venturi jet pump will consume 15-45 LPH. Take this fuel loss into consideration when sizing the fuel pumps.
2. If it is important for fuel pressure to hold steady after the engine is shut down, install one of these CHECK VALVES somewhere in the fuel system.

FUEL PUMP INFORMATION
All kits come partially assembled with the final assembly performed by the technician during installation. Refer to the instructions above for more details.

If a ""Pumps Not Included"" option is selected, the kit will have enough parts to run 1 or 2 fuel pumps and the user must supply their own compatible fuel pumps.

If a ""Pumps Included"" option is selected, the kit will include the fuel pump(s) and corresponding sock filter(s). NOTE: When the unit is purchased with one pump included, additional parts will be needed to install a second pump.

This system supports the following fuel pumps:
Walbro F90000267 E85
Walbro F90000274 E85
Walbro F90000285 E85
Walbro GSS342 255lph
AEM 50-1200 E85
Ti Automotive E5LM (brushless)

Notes
1. Single fuel pump installations can re-use the OEM fuel pump controller wiring.
2. It is recommended to upgrade OEM wiring to ensure the pumps are receiving full power and operating at their full potential.
3. Universal fuel pump wiring kits can be found HERE. Select one for each aftermarket pump.

FUEL HANGER FEATURES

-Drop-In Installation
-Anodized Aluminum Construction
-Merged 10AN ORB Female Pump-Out Port
-Restriction-Free 8AN ORB Female Return Port
-Permits 1 or 2 Fuel Pumps
-Brushless Fuel Pump Compatibility
-High Current Electrical Hardware
-Integrated Venturi Jet Pump Siphon
-Fluorosilicone Duckbill Return Valve
-Stainless Steel Hardware and Clamps
-Gasoline, Methanol, and E85 Compliant